人妻暴雨中被强制侵犯在线,亚洲国产欧美日韩精品一区二区三区,四虎影免看黄,国产无人区二卡三卡四卡不见星空

機械社區

標題: 求翻譯 [打印本頁]

作者: jackline 時間: 2011-6-30 00:03
標題: 求翻譯
外語不精，求達人翻譯，謝謝

1：垂直度超差：圖紙要求Φ125±0.011外圓和端面的垂直度公差0.03mm,實測0.06mm

2：平行度超差：圖紙要求部件底部裝配基準面與裝導軌平面平行度0.02mm，實測0.05mm
3：直線度超差：實測導軌止口直線度0.26mm（中凹）
4：尺寸超差：圖紙要求 Φ150+0.04孔中心線與底面尺寸為145±0.03mm,實測144.94mm
5：裝配基準面有2處補焊，凸0.03mm（長15mm寬5mm）附照片

作者: 神奇寶貝 時間: 2011-7-5 11:16
1.Perpendicularity is out of tolerance: drawing's requirement is Φ125±0.011, perpendicularity tolerance of the outer circle and end face is 0.03mm, fact measurement is 0.06mm.
2. Parallelism is out of tolerance: the required parallelism between the bottom assemble datum plane and guide installiaton plane is 0.02mm, fact measurement is 0.05mm.
3. Straightness is out of tolerance: fact measurement of the guide's front edge is 0.26mm(Middle is concave)
4. Dimension is out of tolerance: drawing's requirement is Φ150+0.04, distance between the hole center and the bottom is required 145±0.03mm, fact measurement is 144.94mm.
5. There are two repair-welding on the assemble datum plane, protruding 0.03mm(15mm long and 5mm wide), see attached photo.

作者: jackline 時間: 2011-7-7 20:06
回復 jackline 的帖子

受益匪淺，灰常感謝

還想問個問題：尺寸超差，可以用 Dimension is undersize/oversize,或dimension is not correct表示嗎？

作者: 神奇寶貝 時間: 2011-7-8 12:37

jackline 發表于 2011-7-7 20:06 h! ~# O8 M- q5 o O
回復 jackline 的帖子. \4 z- c: V1 I. g+ [6 ~7 x' ]

6 A- O$ d! L' v n* o! H& J受益匪淺，灰常感謝

沒用過，也沒聽別人這樣用過

作者: 采彡銫莎氵莫 時間: 2011-9-13 08:18
是和公司有關的，又學習了

作者: wugqtop 時間: 2011-9-23 13:42

jackline 發表于 2011-7-7 20:06
' h) b( c2 K: ?. Z. b) O* i回復 jackline 的帖子
& d% o5 j8 s) l" {" L! K4 e3 u# `, ?9 Z/ s; _, h! ~) a/ |8 E# a
受益匪淺，灰常感謝

dimension out of tolerance

作者: kason127 時間: 2011-9-26 17:16
用google翻譯好了??！

歡迎光臨機械社區 (http://www.xa-space.com/)