標題: 那位大俠幫我翻譯成英語?非常感謝! [打印本頁] 作者: 一顆豆芽 時間: 2013-1-10 08:36 標題: 那位大俠幫我翻譯成英語?非常感謝! 1、打槽工裝調整不到位( ?0 Z) E2 ~; I D
1.1、各底座安裝不同軸 . b `5 C( D+ k- w* e1.2、零件安裝的松緊程度不適合 - P( X0 T4 ?* v" z- X: y1.3、壓桿安裝的松緊程度不適合 # b6 C! H* K3 }3 V k6 o1.4、打槽機空間小調整困難7 N2 U. C6 n# U0 {1 I1 K9 h1 n( z
2、加工前沒有檢查沖針的磨損程度1 q. U3 i4 p- O: n! H
3、打槽機工裝不適合M15/M16產品加工 ' q5 Z( o% |2 g: O& o1 E3.1、底座不能安裝高度為2.9mm的產品7 b, b6 F8 j; F; G
3.2、壓桿不能固定OD<75的產品3 [( ?8 z, H8 Z( I
3.3、壓塊不能壓緊產品, E+ A3 Z0 X2 r* s) `' v6 f/ e, R
4、沖針切削阻力大,尺寸變化大" g& W, i2 W& q* [" f
4.1沖針形狀不適合 ( S8 r" m) |- u8 ^7 N7 u$ J5、氣缸不穩定 ' D1 H& F4 y. K+ t7 v5.1、氣壓不穩定 6 D/ _; w0 q' t# M5 a% Q5.2、沖針?biāo)蓜?dòng) # Z" g4 ^0 X* E* Q8 M; Z+ q5.3、氣缸松動 5 {3 \' T8 N W/ N6、產品外徑小,剖面小裝夾困難, c: t0 `. [. o7 S
7、產品易塑性變形,加工困難2 {9 V; m, d7 w; r
8、槽尺寸測量困難6 N* V5 Q p- Q' I: @! n' C |/ {/ c/ n/ q
/ N* S; ~. v5 C- G1 ~5 r, [/ J* n2 s& }5 D9 g1 x. L( c t0 s
兄弟的英語實在是太難了。上面這些需要給老板看,那位好心的幫幫忙??! - [" C4 G1 u+ W作者: 唯獨懂你 時間: 2013-1-10 09:01 In 1, playing the slot tooling adjustment does not reach the designated positionIn 4 y) U6 U/ ^& | 1.1, the base mounting shaft 1 B4 W6 w1 u/ F& d" K1.2, the degree of tightness for mounting parts ! h( q, q8 ?$ ~2 o2 D7 o5 Y1.3, the degree of tightness of the pressure rod is arranged forIn 4 ]3 e; G Z& M1 l# Q" W( ?2 i# i5 [
1.4, playing the slot machine in the whole space is difficultIn 4 N5 p" Z1 @+ {, v2, prior to processing did not check the degree of wear of the punch needleIn - T* P6 i M! H) Y5 x, M/ l3, playing the slot machine tooling is not suitable for M15\/M16 products processingIn - o& ^! w" O/ v% J, e: t' b" V
3.1, the base can not be installed height of 2.9mm products/ W4 b9 K4 W: E+ H, O% Q& N6 O
3.2, push rod can not be fixed OD < 75 productsIn & t/ R' H" {' m! r% x3 L, N* j% o
3.3, the pressing block can not be pressed productsIn ( p0 _7 ]% K' A% W
4, the punching needle big cutting resistance, dimensional change - }1 \* x4 X! N4.1 punch needle shape is not suitable forIn 8 B0 v9 k! e @ 5, the cylinder is not stableIn ; h/ R5 k# C& ] g1 W; I6 r3 }$ c: @5.1, the pressure of not stableIn 0 l$ r7 H2 H5 t7 C
5.2, the punching needle looseningIn ' @# W; v7 g9 f6 z
5.3, the cylinder is looseIn & F: O. F* g- X6, the product of small external diameter, small difficult clamping sectionIn : Y) a' W* ]: D7 B
7, the product easy to plastic deformation, difficult processing 4 P( i! U) v5 M. a2 l: W' @. r8, groove size measurement difficulties以后自己在百度上面可以翻譯,中英文翻譯就行。作者: baikenor 時間: 2013-1-10 10:32
谷歌翻譯 感覺不錯 翻譯之后再翻回去可以驗證有沒有不準確的地方作者: 一顆豆芽 時間: 2013-1-10 10:37
非常感謝各位