人妻暴雨中被强制侵犯在线,亚洲国产欧美日韩精品一区二区三区,四虎影免看黄,国产无人区二卡三卡四卡不见星空

機械社區

標題: 機械英語圖紙技術要求,求大神幫翻譯, [打印本頁]

作者: 海椒喝酒    時間: 2015-5-16 23:16
標題: 機械英語圖紙技術要求,求大神幫翻譯,
請大家?guī)蛶兔?,謝謝了
6 K" F8 }. Q. {9 i$ k8 e- N0 O/ o0 u8 Z" D: [% W

4 q) t; x5 R" @7 Rmachined by threaded
3 e# s8 ~' ^% G- I: _7 ]value prior to threading  `, B; x6 k4 |' z: I
4 n1 t" j- R  N( k5 H9 ?
, s! R  j4 {# \7 @: E: q2 `& ^! `# G
unless otherwise specified all dimensions are in inches and. m& |# @/ k: E- u% Q! e& ]

, q3 O3 @7 ~. ]' V1.overall length is minimum and longer needed to meet customer requirements are always allowed wothout engingeering approval9 V- Z4 X' S) V5 c% Z- t5 T
2.machined supfaces 250 rms max,thd surfaces 125 rms max
# }& G' i9 e7 ]( i7 y) v+ N) Z3.inside raoius 0.30-0.60 max
. [/ T/ N. y% b+ n% z$ k7 E' x4.corner breaks 0.15X45
' a9 g( X- p0 p. p9 p5.concentricity between 2mach.surf.within 0.15 t.i.r
6 I1 Z% r. h" H, p( I6.normality,squareness,parallelism of machined surfaces .005per ingh to a max.of.030for a single surface
! z8 ~' S5 X+ _7.all thread entry&exit angles to be 25-45 off of thread axis. G: G( E2 U2 n

, u# C, r5 }- Q" ]. y
作者: seekfor    時間: 2015-5-17 12:39
本帖最后由 seekfor 于 2015-5-17 12:42 編輯 6 T) Z$ U9 k' }" J5 O( |3 h
, @. }! {2 `- H' ^' g, D* W* R
以下翻譯僅供參考。。1 p0 g1 n2 B! g- V5 m/ L. n
machined by threaded
5 l' T8 y& \$ U- y(不好翻譯,銑螺紋?攻螺紋?), ^+ W$ |/ O( `: `
value prior to threading數值(螺紋大小還是切削進給?)參照車螺紋;& R9 X0 ^) U4 o
unless otherwise specified all dimensions are in inches and- K  _4 X2 }- ^
未注尺寸為英寸,并且. X+ Y& W: l2 }: y7 Q' |
, W# e: l( ]2 C& o' P" y
: {9 K. }* `/ L  O. O6 a1.overall length is minimum and longer needed to meet customer requirements are always allowed wothout engingeering approval
. M* u9 k2 k. |* i. d$ ], ^螺紋有效長度為最小;具體長度在滿足客戶的要求情況下通常不需要工程批準;% U" W  p# ~1 p/ U& S3 I) y
2.machined supfaces 250 rms max,thd surfaces 125 rms max機加工面粗糙度250 RMS  max(相當于Ra6.3 max左右 【轉換關系除以40】) ;螺紋表面粗糙度125 rms max (Ra3.2 max)+
! A' Z1 P* S6 K機加工面 g9 j& Q" b9 ]6 j& T
+ e! \8 a0 v2 F" v
3.inside raoius 0.30-0.60 max未注內圓角 0.3-0.6 max 【不知道產品是啥樣子的,按英制算這倒角是不是有點大?】; M( d# ?0 Q& X  m+ w" ~
?】未注內. Z: u* E, p0 P, A: E3 G

; U5 |& z( L7 n; A4.corner breaks 0.15X45  棱邊倒角0.15X45
, {0 E3 C4 S9 S6 G1 H5.concentricity between 2mach.surf.within 0.15 t.i.r  兩機加面同軸度 0.15 . @' G( W9 n/ H2 K( Q% C( }
+ A! S# m0 }, X4 \6.normality,squareness,parallelism of machined surfaces .005per ingh to a max.of.030for a single surface  機加工表面的垂直度和平行度.005/1  ,對單個表面.030MAX
) @$ I8 ^7 t- U7 ^, h: h7.all thread entry&exit angles to be 25-45 off of thread axis  螺紋孔兩端倒角25-45°  (又或者是銑螺紋時導入導出過渡角度為25-45°)- Z, Q6 R! X  \  V3 l: j) ~
8 \) ~+ E: b: {  [

  Q" e0 J$ m3 R3 l+ T
作者: niufang2    時間: 2015-5-18 07:43
machined by threaded
; Z0 ^; p' J* |" j, tvalue prior to threading
! T3 Q8 [: M6 |! X( |
. F5 b* o5 b% W2 }; Z在加工螺紋前先按照螺紋的參數試走刀(我是連翻連猜測的,沒肯定把握)- r9 H* H7 }2 x/ R6 D, R' g! t9 G

作者: 海椒喝酒    時間: 2015-5-19 21:21
很有幫助,謝謝大家
作者: 星月xingyue    時間: 2015-6-2 16:29
我不懂英語,也經常遇到英語圖紙,頭痛的很!
作者: 龍游大海    時間: 2015-6-7 11:30
機械加工螺紋
作者: 自由的歷程    時間: 2015-6-24 12:30

# f6 Q, Y0 ^) {" J; b9 c, p8 [回帖是一種美德,謝謝啦
作者: 風吹羽飛    時間: 2015-7-26 21:17
給樓主一個建議,可以下載一個有道翻譯軟件,只少簡答的翻譯還是可以做到的。
作者: 冰雨夜    時間: 2015-7-28 14:35
不錯
作者: artisan2014    時間: 2015-7-29 09:29
machined by threaded2 e+ v7 o  h  ]- s
螺紋加工方式
3 v. Z# b$ E2 I1 Q; e9 Svalue prior to threading/ U& S1 r5 A) t" \
攻螺紋之前的尺寸2 _- b( E. d- S  B3 f4 A
unless otherwise specified all dimensions are in inches and. R+ g8 o2 O/ C% `3 ?, d8 s
除了特殊要求外,全部尺寸為英寸單位
6 E8 W+ u! i& R+ X1.overall length is minimum and longer needed to meet customer requirements are always allowed wothout . B3 |; z  h; B. r) A
  m# i" F  R1 |0 J" v! O7 N& h
engingeering approval; I" Y3 K! r5 z( ^) e6 E' k
  總體長度尺寸為最小,若按照客戶要求增長是被允許的,也不需要工程師批準% c3 C7 {1 b' N- Z2 W, m
2.machined surfaces 250 rms max,thd surfaces 125 rms max : B5 n" ~7 ^1 X& N6 ^' ]% ]2 [3 b
  機加工表面粗糙度為250 rms(Ra6.3),螺紋表面粗糙度125rms(Ra 3.2)
9 w" Q6 Y( b. w- ~3.inside raoius 0.03-0.06 in.; F( A6 L+ _- m  p- @. k
  內部半徑為0.8-1.5,1.5為最大! N7 N* z6 Q. f; M* `) t# e
4.corner breaks 0.015X45 in.# q: S2 [! H4 b
  棱邊倒角0.4X45
! |9 `" z1 ^" \+ A: }% }5.concentricity between 2 mach.surf.within 0.015 t.i.r
6 s6 C3 {5 c1 A  兩機器的同心度誤差量在0.4內9 f0 D0 s/ h: e  S! W
6.normality,squareness,parallelism of machined surfaces .005per inch to a max.of.03 for a single surface
# y% i2 ?4 S, j7 W, ]# [3 M  一般的,機加工表面的垂直度和平行度.005/1  ,對單個表面.030/1 MAX
- {$ R8 F8 Z) [6 F7.all thread entry&exit angles to be 25-45 off of thread axis% ~, L2 V: p& \" t8 w  K8 ?; u
  所有螺紋的起始和脫離角都是與螺紋中心軸夾角范圍為25-45 deg5 o) n2 B% D3 }& o  r) ?

作者: 戀上“你"了    時間: 2015-7-29 10:31
我平時都是用有道翻譯的,基本上能理解大概的意思就好了
作者: 木幾械3.0    時間: 2015-8-7 15:27
翻譯得不錯,贊
作者: kobe愛學習    時間: 2015-8-8 07:26
學習一下6 z& Y" O/ K- x





歡迎光臨 機械社區 (http://www.xa-space.com/) Powered by Discuz! X3.5