美國的斜齒輪圖紙的英文,誰能幫忙翻譯下,不勝感激!

yang13564

1.
Quality: ANSI/AGMA 2000-a88-q11, full depth, full fillet.

2.
FOR LEAD, CROWN, AND PROFILE TOLERANCES SEE DWG 54773379

3.
CROWN DRIVEN GWAR ONLY

4.
NORMAL PRESSURE ANGLE 20”

5.
3 o1 w' I' n- _) ~5 t  e& y( O, U; T& ]NORMAL DIAMETRAL PITCH 8

6.
8 \4 N8 w3 ?, r' }2 ?$ @NORMAL CIRAULAR PITCH 0.3927

7.
: J$ w0 ?6 K9 \9 O! k; ?. P0 gHELIX ANGLE:16.6011

8.
BACKLASH TO BE 0.996” TO 0.008” ON 6.9784” CENTERS

9.
. ~, A2 ^( G- {7 rMATERIAL: AISI 8620

10.
* y* c! z1 ]- D( a; ZCASE CARBURIZE TO 0.025” TO 0.040” EFFECTIVE FEPTH AFTER GRINDING AND HARDEN TO 57-61 RC, CORE HARDNESS
" z) b$ j/ K0 vTO BE 25-40 RC.

11.
3 E4 c. Z; p. m' M$ e7 iRETAINED A USTENITE – 5% MAXIMUM BY VISUAL INSPECTION.

12.
EACH GEAR DEAR SET TO BE BOXED SEPARATELY AS A SET AND EACH GEAR MARKED WITH THE SET PART NUMBER ON THE OUTSIDE. EACH GEAR TO HAVE P/N AND SUPPLIER INENTIFICATION STAMPED. EACH GEAR TO HAVE P/N AND SUPPLIER IDENTIFICATION SATAMPED OR ELECTRIC ACID ETCHED AS SHOWN, APPROX. TEXT HGT..25’.

13.
REMOVE ALL CHIPS FROM TAPPED HOLES.

NUMBER OF TEETH

HAND OF HELIX

LEAD OF HELIX

PIRTCH DIAMETER

BASE CIRCLE DIAMETER

ADDENDUM

WHOLE DEPTH

TRANSVERSE CIRCULAR

TOOTH THICKNESS WO/BL

NORMAL CIRCULAR

TOOTH THICKNESS WO/BL

yang13564

4 R8 Z5 R9 @8 U沒有人翻譯,找到了資料,不知道對不對!望高手出來指正!
" W* {* c) \4 g2 z7 J) p9 A        齒輪制造標準和精度等級：ANSI/AGMA 2000-A88，精度12級，全深，全倒角。
. d' R0 z4 n& L0 _        齒向、齒形修緣和漸開線輪廓公差按54773379圖紙規定。
        僅驅動齒輪鼓形修整。
2 g4 y5 P4 }5 F# X7 b        齒形壓力角20º
        節徑DP=10
% Y! N# ?% V5 N6 M        齒距：0.3142
        螺旋角：15.9355º
0 u- I# U9 e8 r3 l$ q# c% {        在齒輪嚙合中心距5.5118”上，側隙要求在0.006” ~0.010”之間。
) L! k& o' U) u* I        齒輪材料：AISI 8620
* _5 Q6 {. W9 j2 B: P4 Z- u        滲碳層0.025”~0.040”有效深度，表面硬度為57~61Rc，芯部硬度25~40Rc。
; v, G' |. B3 b5 P: q; F        殘余奧氏體最大5%目測檢查。
        每個周轉盒內只能裝一個齒輪組，周轉盒外標記齒輪組圖號，齒輪表面須按圖示部位用電蝕法標記零件號和供貨商代碼，字高約0.25。
        攻絲后，去除螺紋孔內的鐵屑。

qvzhiwei

樓上玩意的好專業，佩服?。。?/td>

another

二樓挺專業的···感覺還不錯，很值得學習。