求翻譯

jackline

外語不精，求達人翻譯，謝謝

) D* L; T3 s. Q2 I. [1：垂直度超差：圖紙要求Φ125±0.011外圓和端面的垂直度公差0.03mm,實測0.06mm
) O3 }- ?1 }- V" ^4 w* V1 G2 Y* s
) p. Y9 b: ]$ b3 n2：平行度超差：圖紙要求部件底部裝配基準面與裝導軌平面平行度0.02mm，實測0.05mm
1 K8 [& d+ x7 ]0 z& [6 F3：直線度超差：實測導軌止口直線度0.26mm（中凹）
4：尺寸超差：  圖紙要求 Φ150+0.04孔中心線與底面尺寸為145±0.03mm,實測144.94mm
5：裝配基準面有2處補焊，凸0.03mm（長15mm寬5mm）附照片
- s6 m( F4 N! q8 u3 p( j

神奇寶貝

1.Perpendicularity is out of tolerance: drawing's  requirement is Φ125±0.011, perpendicularity tolerance of the outer circle and end face is 0.03mm, fact measurement is 0.06mm.
2 U/ K& F: L/ |6 f2. Parallelism is out of tolerance: the required parallelism between the bottom assemble datum plane and guide installiaton plane is 0.02mm, fact measurement is 0.05mm.
2 a. W- e8 V4 E& V8 {3. Straightness is out of tolerance: fact measurement of the guide's front edge is 0.26mm(Middle is concave)
) s; e4 m( r& s4. Dimension is out of tolerance: drawing's  requirement is Φ150+0.04, distance between the hole center and the bottom is required 145±0.03mm, fact measurement is 144.94mm.
5. There are two repair-welding on the assemble datum plane, protruding 0.03mm(15mm long and 5mm wide), see attached photo.

jackline

回復 jackline 的帖子

/ _+ W7 V) M/ N1 v3 ?受益匪淺，灰常感謝
還想問個問題：尺寸超差，可以用 Dimension is undersize/oversize,或dimension is not correct表示嗎？
) y9 A! y  V/ r6 ^$ V1 r( V
; v" y& N& v9 w, z( D
+ l2 G2 ^' Z4 c3 k4 ^1 E

神奇寶貝

jackline 發表于 2011-7-7 20:06
回復 jackline 的帖子

受益匪淺，灰常感謝

- k; [" X" S$ j沒用過，也沒聽別人這樣用過

采彡銫莎氵莫

是和公司有關的，又學習了

wugqtop

jackline 發表于 2011-7-7 20:06
! d: T, q  {( `回復 jackline 的帖子

受益匪淺，灰常感謝

dimension out of tolerance
. G. N) W% Y1 R& U# h/ L; D

kason127

用google翻譯好了??！