求翻譯

jackline

外語不精，求達人翻譯，謝謝

1：垂直度超差：圖紙要求Φ125±0.011外圓和端面的垂直度公差0.03mm,實測0.06mm
* W  F. |, h/ R) k* Z
: S* H6 I, }2 g- e5 y2：平行度超差：圖紙要求部件底部裝配基準面與裝導軌平面平行度0.02mm，實測0.05mm
3：直線度超差：實測導軌止口直線度0.26mm（中凹）
4：尺寸超差：  圖紙要求 Φ150+0.04孔中心線與底面尺寸為145±0.03mm,實測144.94mm
2 g8 \. S8 ^) Q  k( g8 N3 ~5：裝配基準面有2處補焊，凸0.03mm（長15mm寬5mm）附照片
8 K, G8 ^: r0 w; s; }

神奇寶貝

1.Perpendicularity is out of tolerance: drawing's  requirement is Φ125±0.011, perpendicularity tolerance of the outer circle and end face is 0.03mm, fact measurement is 0.06mm.
2. Parallelism is out of tolerance: the required parallelism between the bottom assemble datum plane and guide installiaton plane is 0.02mm, fact measurement is 0.05mm.
+ ~2 Q3 c' i0 ?: p: c3. Straightness is out of tolerance: fact measurement of the guide's front edge is 0.26mm(Middle is concave)
4. Dimension is out of tolerance: drawing's  requirement is Φ150+0.04, distance between the hole center and the bottom is required 145±0.03mm, fact measurement is 144.94mm.
3 S( B( ]4 x0 |2 W5. There are two repair-welding on the assemble datum plane, protruding 0.03mm(15mm long and 5mm wide), see attached photo.

jackline

回復 jackline 的帖子
! I( V, N  \( _
$ N$ ?5 ]1 Y/ ^, Y0 U3 d; i# u受益匪淺，灰常感謝
* r: O1 d7 ~5 F9 T" X$ \  l% T還想問個問題：尺寸超差，可以用 Dimension is undersize/oversize,或dimension is not correct表示嗎？
" W4 V1 d5 L9 Y1 v

神奇寶貝

jackline 發表于 2011-7-7 20:06
9 T! S$ ]# O& q$ y- _0 s4 L( R: S回復 jackline 的帖子
$ e1 ^9 m7 F9 {7 A* E4 u! V; |2 y
/ K( c0 m% S& l7 v+ H3 z0 L3 S& B& B受益匪淺，灰常感謝

. W# N; w3 P8 j9 p# N. o7 t8 ~沒用過，也沒聽別人這樣用過

采彡銫莎氵莫

是和公司有關的，又學習了

wugqtop

jackline 發表于 2011-7-7 20:06
. T  c7 Y$ X, j6 h" A, Y, l4 }回復 jackline 的帖子

* c; j! i* }8 q2 Y- m受益匪淺，灰常感謝

8 F, O7 L# v# o  J/ _dimension out of tolerance

kason127

用google翻譯好了??！