[4A] 這張齒輪圖紙的技術說明，你能看出哪里需要完善？

十年一夢

大家討論一下有什么需要完善之處。

NOTES:
, o8 m0 p9 R5 A4 d. l4 q2 V1. MATERIAL: ALLOY STEEL 9310H-NORMALIZED & TEMPERED TP HRc 32-40
(AIR CRAFT QUALITY FORGING).
2. CENTERS ARE MANDATORY ON BOTH ENDS OF SHAFT. ALL DIAMETERS MUST
+ I+ B' M8 |8 r: mBE MACHINED USING THESE CENTERS AND -A- & -B- DIAMETERS MUST BE
CONCENTRIC TO THESE CENTERS WITHIN 0.005 TIR.
, w* A: l8 T9 c  I3 C" b3. DYNAMICALLY BALANCE WITHING 0.26 OZ-IN AT PLANES INDICATED.
INSTALL HALF-KEY IN THE KEYWAY DURING BALANCING.
- R$ o  ]! g  l# y$ m4. PROTECT THESE SURFACES FROM SCRATCHES AND TOOL MARKS.
5. WHILE HOBBING LEAVE .29-.30 GRINDING STOCK TO FINISH THE GEAR.
. o; C3 i2 w- D: V6. CASE CARBURISE AREA MARKED (**) AND HARDEN TO RC 58-64. FINISHED
CASE DEPTH TO BE RC 50 AT 0.4-0.6 DEEP. REMAINDER TO BE RC 32-40.
7. GRIND THE TEETH PER GEAR DATA AFTER HARDENING.
& d1 k" R) \5 b: f4 Z1 h* w8. DO NOT GRIND ROOT OF GEAR TOOTH. USE PROTUBERANT HOB.
- W* W9 B) @9 R) l5 e9. ALL FILLET RADII TO BE CAREFULLY BLENDED, POLISHED AND FREE OF
7 z9 Q& G6 \; Q) a1 N7 x/ zTOOL MARKS.
10.UNLESS OTHERWISE SPECIFIED, CONCENTRICITY, SQUARENESS &
5 `+ ?0 ~/ M" ~- X; v- [: d1 e' fPARALLELISM TO BE WITHIN 0.254 TIR
% a: a0 F) {0 t9 K6 J" {4 [11.GEAR ACCURACY DATA TO BE DETERMINED FROM DATUM -A- & -B- (SHAFT).
! U& Z% X0 m# F1 f3 Y9 A9 X3 A12.MAGNETIC PARTICLE TEST AND INSTPECT.
13.AFTER FINAL GRINDING, BLEND ALL SHARP EDGES, REMOVE ALL BURRS.
14.BURNISH MARKED AREA WITH (*).

機械神話

希望看到這張圖，機械圖紙是圖文并存的，不可分離。

itwotwo

這是你自己出圖紙給鬼佬加工的？
1. MATERIAL: ALLOY STEEL 9310H-NORMALIZED & TEMPERED TP HRc 32-40.(AIR CRAFT QUALITY FORGING).
材質應寫入材質欄，這里只要寫熱處理方式和最終硬度
2. CENTERS ARE MANDATORY ON BOTH ENDS OF SHAFT. ALL DIAMETERS MUST BE MACHINED USING THESE CENTERS AND -A- & -B- DIAMETERS MUST BE CONCENTRIC TO THESE CENTERS WITHIN 0.005 TIR.
這里的軸可能用axis比較合適，因?yàn)檫@根軸線不是實際存在的東西，同軸度本身就是個跳動值所以不用TIR。更應該直接標在圖上。
( b0 m2 |$ Y& }" f3 `3.DYNAMICALLY BALANCE WITHING 0.26 OZ-IN AT PLANES INDICATED INSTALL HALF-KEY IN THE KEYWAY DURING BALANCING.
半鍵連接？動平衡因該在整根軸帶齒輪的裝配體完成后整體做的，把這個要求寫在這里應該要REF一個裝配圖要求。
4. PROTECT THESE SURFACES FROM SCRATCHES AND TOOL MARKS.
保護刮傷正常，保護刀痕不正常。刀痕都是加工出來的，不存在保護就會消失。
5. WHILE HOBBING LEAVE .29-.30 GRINDING STOCK TO FINISH THE GEAR.
？這是客戶對供應商的產品需求嗎？怎么看起來像打工做工藝分析的？
4 ?) f0 H) I. W9 s. O6. CASE CARBURISE AREA MARKED (**) AND HARDEN TO RC 58-64. FINISHED CASE DEPTH TO BE RC 50 AT 0.4-0.6 DEEP. REMAINDER TO BE RC 32-40
: c0 i  B' v5 a7 h+ j% S7. GRIND THE TEETH PER GEAR DATA AFTER HARDENING
8. DO NOT GRIND ROOT OF GEAR TOOTH. USE PROTUBERANT HOB.
- H1 H8 |7 L( q6 T這是不是滾壓齒底的意思？用roll
- Z6 A& W! g- D8 p9. ALL FILLET RADII TO BE CAREFULLY BLENDED, POLISHED AND FREE OF TOOL MARKS.
倒角處訂個1.6的光潔度就行
10.UNLESS OTHERWISE SPECIFIED, CONCENTRICITY, SQUARENESS & PARALLELISM TO BE WITHIN 0.254 TIR
3 \1 \5 c& D& K同軸度，垂直度，平行度都要有參照標準的，哪有可能沒有specified??？而且本身這3個值本身就是TIR，不需要說明
12.MAGNETIC PARTICLE TEST AND INSTPECT.
. k) ^" _$ U2 p. R探傷之后要說哪些區域有傷可接受或者全部不接受
! c+ d& r2 V3 C$ c- Q0 w13.AFTER FINAL GRINDING, BLEND ALL SHARP EDGES, REMOVE ALL BURRS.
1 D) y* j3 }2 K1 P0 e' x1 \我通常會用Break all burr. Sharp edge本身在機械零件里不是缺陷，該有的地方是你設計成它有。要是日用品就不能存在sharp edge。
14.BURNISH MARKED AREA WITH (*).
* a# W3 I, W% q2 R4 J
老兄的東西每次看都有新發現。但是如果是一個齒輪的note，好像該有的東西全部沒有：
' |4 i8 Y& e  rtop circle
5 L$ ~! c/ K; Nroot circle
addendum
dedendum
tooth height
pitch distance
3 L) f8 f7 j( @& `' v這些都應該有上下公差或者標準值
presure angle應該要指出

qdtruck

沒有圖紙?jiān)趺捶治霭?？樓上有圖紙了？

supperslz

無圖無真相另，另外還要說一下功用。

271211310

你需要的是真正的高手

宇宙立方

愛顯擺也是人類原罪之一

湘中人

無圖無真相！！

云飄映月

高手啊，三樓

混日子

樓主你這應該是單個零件的技術要求吧？我覺得第三條動平衡應該去掉，單個零件的在這沒什么用；第五條磨削余量沒必要寫在這個里面吧，畢竟是工藝要求；另外，你要求表面刀紋看不出，那就直接定個粗糙度Ra1.6以下，這個可去參考粗糙度標準樣塊；第十條未注同心度0.254你有和第三條校核沒？單位是英制還是公制？有必要到小數點后三位？還有最后那條不太清楚你要干什么。